Experimental investigation and numerical simulation analysis of sintered micro-fluidic devices

ABSTRACT

This study investigates the use of numerical simulations to describe the solid-state diffusion of a sintering stage during a metal injection moulding process for micro-fluidic components with 316L stainless steel powders. Finite element (FE) analysis based on a thermo-elasto-viscoplastic model was conducted to describe the densification process of a stainless steel porous component during solid-state sintering. The numerical analyses, which were performed on a 3D micro-structured component with various powder volume loadings to take into account the thermal debinding effect to propose a full debinding sintering simulation, demonstrated that the FE simulation results are in agreement with the experimental ones.     

Characterization of superficial modification of ferrous rusted substrates subjected to dechlorination-electrochemical process

Preservation of archaeological artefacts after their removal from saline media is a difficult task due to the chloride content of the oxide layers which are unstable in atmospheric conditions, especially if the relative humidity exceeds 85%. For this reason, removal of chlorides from rust layers is one of the priorities of conservationists or restorers of historical artefacts. However, removal of chloride ions is not an easy procedure because of the many considerations involved in the process. In this research, artificially pre-rusted iron samples and an actual historical cannonball were subject to a dechlorination process in a potassium hydroxide solution to measure constant chloride release in a bulk solution. After the chloride removal process, a commercial protective layer was applied to the rust for stabilization purposes. It was calculated that the kinetics of the dechlorination process is driven by diffusion behaviour following Fick’s second law. When this diffusion process prevails, the dechlorination extraction affects the integrity of rust layers as is demonstrated with scanning electron microscopy and X-ray diffraction analyses. It was proven that the chloride removal procedure causes the studied iron layers to stiffen, provoking superficial modification and, in some cases, fractures of the rust. By means of electrochemical impedance spectroscopy it was calculated that the magnitude of the positive effect of the dechlorinated samples depends on the protective features of the rust. Therefore, this research reveals that an efficient chloride removal procedure depends on the electrochemical properties of the dechlorination process and the initial morphology of the iron rust.     

Microstructure evolution during thermomechanical processing in 3Mn-0.1C medium-Mn steel

ABSTRACT

Medium-Mn steels are energetically investigated as a candidate of the third generation advanced high strength steels (AHSSs). However, their phase transformation and microstructaure evolution during various heat treatments and thermomechanical processing are still unclear. The present study first confirmed the kinetics of static phase transformation behaviour in a 3Mn-0.1C medium-Mn steel. Hot compression tests were also carried out to investigate the influence of high-temperature deformation of austenite on subsequent microstructure evolution. It was found that static ferrite transformation was quite slow in this steel, but ferrite transformation was greatly accelerated by the hot deformation in austenite and ferrite two-phase regions. Characteristic dual-phase microstructures composed of martensite and fine-grained ferrite were obtained, which exhibited superior mechanical properties.

This paper is part of a Thematic Issue on Medium Manganese Steels.     

Friction stir welding of API X70 steel incorporating Ti-dioxide

In the present work, the microstructural evolution and hardness of HSLA X70 joined by friction stir welding were investigated. The FSW was applied to HSLA X70 with and without the addition of titanium dioxide (TiO₂) powders. To evaluate the microstructural features and hardness of different weld zones, optical microscopy and Vickers microhardness measurements were applied. The results show that the distribution of TiO₂ powders is strongly dependent on the applied friction stir processing, which in turn changed significantly the microstructure and hardness profile. In this regard, the optimum stirring action resulted in a homogeneous and fine dispersion of particles leading to the domination of an acicular ferrite phase with a hardness of 370 HV. On the other hand, the lower stirring action resulted in coarse particles as well as the development of the polygonal ferrite structure with a hardness of ～185 HV.     

超高强韧油井管合金设计与高强韧机制

 为了揭示1 000 MPa级低碳加铌钒钛微合金钢的高强韧机制,研究了S1(w(C)=0.09%)与S2(w(C)=0.17%)两种合金成分的油井管钢成分-工艺-组织-性能关系。试验表明,两种成分试验钢经水淬后的组织分别为板条贝氏体加少量马氏体和马氏体加少量贝氏体的复相组织。两种成分钢经过450~600 ℃、30 min的中温回火后,组织中均出现碳化物析出,且S1试验钢回火后的屈服强度基本不变,抗拉强度下降了约70 MPa,S2试验钢回火后的屈服强度与抗拉强度迅速升高170 MPa左右。溶度积公式的计算结果表明,两种钢的水淬组织中铌、钛元素析出彻底且析出物的体积分数都很小,因此回火铁素体基体中的VC析出强化对S1试验钢回火后屈服强度保持不变以及S2试验钢回火后屈服、抗拉强度提高起到重要作用。     

钢铁生产的水能关系分析

从钢铁生产过程中水资源使用时的能耗角度研究了钢铁联合企业的水能关系，提出了水能强度的概念来评价企业生产过程中水资源利用的节能水平，建立了钢铁企业的水能关系模型。以中国某大型钢铁联合企业为例，计算并分析了该企业的水能关系。该企业总的水能量为55 709 kW·h/h，重复用水水能量占整个钢铁企业全部水能量的82%，补水水能量占16%，排水水能量占1%；各工序中热轧工序占比最大，其次是炼铁、炼钢工序，冷轧、烧结和炼焦工序较低。该企业的吨钢水能强度为0.208 kW·h/m3，炼铁工序的水能强度最高，热轧、炼钢工序次之，烧结、冷轧和炼焦工序较低。最后，从钢铁生产过程水资源利用的角度得到节能的方向及措施。     

DOPO‐Based Phosphorus‐Containing Methacrylic (Co)Polymers: Glass Transition Temperature Investigation

A two‐step synthetic procedure is designed for preparing new flame‐retardant methacrylic monomers containing 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) as a substituent side group. DOPO and methacrylate moieties are linked by linear aliphatic hydrocarbon spacers (3 to 11 carbon atoms). Copolymerization with methyl methacrylate is carried out leading to copolymers containing between 2 and 10 wt% phosphorus. All homo‐ and copolymers exhibit a unique glass transition temperature (T_g ). A new group contribution for DOPO‐based substituent is extracted that leads to reasonable estimations of T_g s of other published polymers. The Fox equation provides a good estimation of T_g s for most copolymers and for physical blends of poly(methyl methacrylate) (PMMA) and DOPO. When using monomers having three and four carbon atoms in the hydrocarbon spacer, the T_g of copolymers remains close to that of PMMA over a wide range of composition.     

Developing high-performance laminated Cu/TiC composites through melt infiltration of Ni-doped freeze-cast preforms

Nacre-inspired laminated composites have been proven to possess a unique combination of strength and toughness. In this study, we fabricated nacre-mimetic Cu/TiC composites via unidirectional freezing of aqueous TiC slurries containing different amounts of NiO additives, followed by ice sublimation, carbothermal reduction of NiO to Ni during sintering and then gas-pressure infiltration of the Cu melt. The introduction of Ni greatly facilitated the densification of ceramic lamellae and enhanced the interfacial bonding between Cu and TiC. The resultant composites displayed outstanding damage tolerance and anisotropic electrical conductivities. Specifically, for an ～31?vol% TiC–Cu composite containing 24?wt% Ni in the ceramic lamellae (based on the TiC content), a fracture toughness (K_Jc) of 72.5?±?1.0?MPa·m^1/2, work of fracture of 53.4?±?3.5?kJ/m², bending strength of 725?±?11?MPa and longitudinal electrical conductivity of 22.7?MS/m (～60% of the Cu matrix) were achieved, which were approx. 81%, 536%, 122% and 97% higher than those of the Ni-free composite, respectively. Noticeable toughening was demonstrated to be a consequence of multiple cracking, plastic deformation and uncracked-ligament bridging of the metal layers, as well as crack deflection and blunting. On the other hand, significant strengthening resulted from tailoring the microstructures in the ceramic layers and at the Cu/TiC interface as a result of Ni doping. We believe that the facile strategy adopted herein provides an effective way to solve the problems of wetting and bonding related to metal infiltration and can be readily extended to the preparation of other nacre-inspired metal?ceramic composites.